Demodulator Information

Demodulation is the act of extracting the original information-bearing signal from a modulated carrier wave. A demodulator is an electronic circuit (or computer program in a software defined radio) that is used to recover the information content from the modulated carrier wave.^[1]

These terms are traditionally used in connection with radio receivers, but many other systems use many kinds of demodulators. Another common one is in a modem, which is a contraction of the terms modulator/demodulator.

History

Since the early days of radio when all transmissions were in Morse Code, a demodulator has also been called a detector. Early demodulators had only to detect the presence (or absence) of a radio wave using a device such as a coherer, without necessarily making it audible. This alternate term has survived despite the greater sophistication of modern circuits.

Techniques

There are several ways of demodulation depending on how parameters of the base-band signal are transmitted in the carrier signal, such as amplitude, frequency or phase. For example, for a signal modulated with a linear modulation, like AM (Amplitude Modulated), we can use a synchronous detector. On the other hand, for a signal modulated with an angular modulation, we must use an FM (Frequency Modulation) demodulator or a PM (Phase Modulation) demodulator. Different kinds of circuits perform these functions.

Many techniques—such as carrier recovery, clock recovery, bit slip, frame synchronization, rake receiver, pulse compression, Received Signal Strength Indication, error detection and correction, etc. -- are only performed by demodulators, although any specific demodulator may perform only some or none of these techniques.

AM radio

An AM signal encodes the information onto the carrier wave by varying its amplitude in direct sympathy with the analogue signal to be sent. There are two methods used to demodulate AM signals.

The envelope detector is a very simple method of demodulation. It consists of a rectifier (anything that will pass current in one direction only), and a low-pass filter. The rectifier may be in the form of a single diode, or may be more complex. Many natural substances exhibit this rectification behaviour, which is why it was the earliest modulation and demodulation technique used in radio. The filter is usually a RC low-pass type, but the filter function can sometimes be achieved by relying on the limited frequency response of the circuitry following the rectifier. The crystal set exploits the simplicity of AM modulation to produce a receiver with very few parts, using the crystal as the rectifier, and the limited frequency response of the headphones as the filter.

The product detector multiplies the incoming signal by the signal of a local oscillator with the same frequency and phase as the carrier of the incoming signal. After filtering the original audio signal will result. This method will decode both AM and SSB, although if the phase cannot be determined a more complex setup is required.

An AM signal can be rectified without requiring a coherent demodulator. For example, the signal can be passed through an envelope detector (a diode rectifier and a low-pass filter). The output will follow the same curve as the input baseband signal. There are forms of AM in which the carrier is reduced or suppressed entirely, which require coherent demodulation. For further reading, see sideband.

FM radio

Frequency modulation or FM is more complex. It has numerous advantages over AM, such as better fidelity and noise immunity. However, it is much more complex to both modulate and demodulate a carrier wave with FM, and AM predates it by several decades.

There are several common types of FM demodulator:

• The quadrature detector, which phase shifts the signal by 90 degrees and multiplies it with the unshifted version. One of the terms that drops out from this operation is the original information signal, which is selected and amplified.
• The signal is fed into a PLL and the error signal is used as the demodulated signal.
• The most common is a Foster-Seeley discriminator. This is composed of an electronic filter which decreases the amplitude of some frequencies relative to others, followed by an AM demodulator. If the filter response changes linearly with frequency, the final analog output will be proportional to the input frequency, as desired.
• A variant of the Foster-Seeley discriminator called the ratio detector ^[2]
• Another method uses two AM demodulators, one tuned to the high end of the band and the other to the low end, and feed the outputs into a difference amp.
• Using a digital signal processor, as used in software-defined radio.

PM

QAM

QAM demodulation requires a coherent receiver.

See also

• Detection theory
• Detector (radio)
• Fax demodulator

References

1. ^ "Demodulator - Definitions from Dictionary.com". dictionary.reference.com. http://dictionary.reference.com/browse/Demodulator. Retrieved 2008-05-16.
2. ^ "The ratio detector"

Categories: Communication circuits | Radio electronics | Radio modulation modes | Telecommunication theory

Related 'Demodulator' Searches: